Problem: I've gotten locked out of my brand new P1632. At first, the default Dealer Code 456789 worked fine, and I was programming successfully, but now I can't get in. I never entered a new dealer code, and never connected to a monitoring service or any other programmer that might have changed it, so I'm not sure why the default code won't still work. Here's what happened: I started installing a new P1632 (rev 30J firmware) to replace a defective P1632. I'm using the three existing keypads (two RP1CAe2 and one RP2ASe2) and an existing GEM-RCVR96. I am programming from keypad since I don't yet have Quickloader.

I had many things programmed successfully, 28 zones, 1 2-wire fire zone, etc. All 14 wired zones are looking good and working right. However, I was having trouble with RF Transmitter Point programming (Zn01-XX).

Programming the GEM-P1632 Control Panel with the. GEMINI SYSTEM READY 01/01. This manual supports the keypad programming of the GEM-P1632 control panel with the. 1 333 Bayview Avenue Amityville, New York 11701 For Sales and Repairs, (800) 645-9445 For Technical Service, (800) 645-9440 GEM-P1632 QUICK START.

View and Download NAPCO Gemini GEM-P1632 programming instructions manual online. CONTROL PANEL/COMMUNICATOR WITH KEYPADS. Gemini GEM-P1632 Control Panel pdf manual. View and Download NAPCO Gemini GEM-P1632 installation instructions manual online. CONTROL PANEL/COMMUNICATOR. Gemini GEM-P1632 Control Panel pdf manual.

It wouldn't take RF ID codes manually and wouldn't go into quick enroll either. So I exited out of programming (hit reset twice). I then successfully reentered programming with default Dealer Code 456789. It asked me again how many keypads.

Magic School Bus Episodes Full Episodes Youtube more. I then hit 'Yes' or 'Menu' many times (can't remember which) to forward through the rest of the options to get to the end of programming and then exited out with Reset. I did not enter anything in any of these options – just hit Yes/Menu to fall through. However, now I can't get in with the default Dealer Code any more. I didn't change it. I never entered a new code in the 'Dealer Code' menu; however, I do think I passed through the 'Dealer Code' menu as I was pressing 'Yes' or 'Menu' to get to the end.

Free Program Licencia Driver Genius Professional Edition 9 on this page. Does forwarding through the menus hitting 'Yes'/'Menu' all the way change the Dealer Code? Seems like it shouldn't. I've since tried 456789, 000000, 111111, etc.

Many times, power-cycled, etc. Nothing works. Questions: 1) Any Idea of what the dealer code might be given the steps I took above? 2) Will I be able to get in with Quickloader once I get the software? 3) Is there any way to 'default reset' the Dealer Code or totally reset the programming? I'm good with a soldering iron, so if there's a test point to hook to ground to reset the system, I can do it. I just need to know which pins on which parts.

4) Any other ideas? To change the dealer code you have to get to the dealer code section, enter in a new code and hit enter ( on/off) key, then it will ask you to do it again. Minimum Passing Score Microsoft Exams Certification. So its doubtful that you changed it. You can only enter dealer mode from the keypad addressed as 1.

So make sure that you are using the address 1 keypad. Did you configure the keypads before installing them? Try removing all keypads and hookup only the original keypad that you used for programming and try to get in. Maybe somehow the system is getting confused by another keypad. You can only default the panel in the dealer mode.

There is no hardware default that you can do on the panel itself. Also what does the keypad do or say when you try to enter programming?

Hi, Thanks for the response, Fishlips. This is keypad number 1. I have verified that from the keypad programming menu: 11123. I even disconnected my #1 keypad and reprogrammed the other RP1 keypad as keypad 1, and got the same results: no response to the Dealer Code. Incidentally, earlier before I got locked out, all keypads were working, but now that I'm locked out, keypads 2 and 3 say 'out of System' and keypad 1 is the only one that works at all. I can switch which keypad is keypad 1, and that one will start working, but only the keypad numbered 1 works at all.